Philips CMD305A/05 Instrukcja Użytkownika Pobierz pdf

Bluetooth V2.1 or later

Quick start guide

Краткое руководство

www.philips.com/welcome

Always there to help you

CMD305A

Question?

Contact

Philips

All registered and unregistered trademarks are property of

their respective owners.

CMD305A_05_QSG_V2.0

Congratulations on your purchase, and welcome to Philips! To

fully beneﬁ t from the support that Philips offers, register your

product at www.philips.com/welcome.

Read and understand all instructions before you use

this product. If damage is caused by failure to follow the

instructions, the warranty does not apply.

1 What’s in the box (Fig. 1)

1 Main unit and front panel

(with a sleeve)

2 Trim plate

3 ISO standard connector 4 Rubber cushion

5 1 x Screw 6 2 x Disassembly tools

7 USB cable 8 User manual

9 Quick start guide

5 REAR LINE OUT R

(Socket)

Rear right speaker

6 OE REMOTE (Brown) OE remote

7 FRONT LINE OUT L Front left speaker

8 FRONT LINE OUT R Front right speaker

Tip

• The pin arrangement for the ISO connectors depends on the type of vehicle

you drive. Be sure to make proper connections to prevent damage to the

system.

Mount into the dashboard (Fig. 3)

If the car does not have an on-board drive or navigation

computer, disconnect the negative terminal of the car battery.

• If you disconnect the car battery in a car that has an on-board drive

or navigation computer, the computer may lose its memory.

• If the car battery is not disconnected, to avoid short-circuit, make

sure that the bare wires do not touch each other.

1 Make sure that the car dashboard opening is within the

indicated measurements. (Fig. 3 - 1)

2 Install the sleeve into the dashboard and bend the tabs

outwards to ﬁ x the sleeve. (Fig. 3 - 2)

Note

• If the system is not ﬁ xed by sleeve but by the supplied screws,

skip this step.

Place the supplied rubber cushion over the end of the

mounting bolt. (Fig. 3 - 3)

4 Slide the system into the dashboard until you hear a “click”.

(Fig. 3 - 4)

5 Attach the trim plate. (Fig. 3 - 5)

6 Reconnect the negative terminal of the car battery.

3 Power on

Press .

» [WELCOME] scrolls.

• To power off the system, press and hold until [GOODBYE] is

displayed.

4 Set the clock

1 Press and hold to access the system menu.

2 Press repeatedly until [CLOCK] and the current time are

displayed.

» If the clock is not set before, [--:--] is displayed.

Rotate to set the hour.

4 Press to conﬁ rm.

5 Rotate to set the minute.

6 Press to conﬁ rm.

2 Press a numeric key to select a preset station.

7 Play from a USB storage device

(Fig. 5)

This system can play .mp3 and .wma ﬁ les that are copied onto

a compatible USB storage device.

Note

• Philips does not guarantee compatibility with all USB storage

devices.

• NTFS (New Technology File System) ﬁ le system is not supported.

Connect the USB storage device to the socket.

2 Press repeatedly until [USB] is displayed.

» Play starts automatically.

If play does not start automatically,

Press / to select a folder.

2 Press / to select a ﬁ le.

3 Press to start play.

8 Listen to an external device (Fig.

9 Use Bluetooth devices (Fig. 7)

With this car audio system, you can listen to audio from a

player or make a call through Bluetooth.

Pair a device

Note

• Philips does not guarantee the compatibility with all Bluetooth

devices.

• Before pairing a device with this system, read its user manual for

Bluetooth compatibility. Make sure that the Bluetooth ﬁ rmware

version of the device is V2.1 or later.

• Make sure that Bluetooth function is enabled on your device, and

your device is set as visible to all other Bluetooth devices.

• The operational range between this system and a Bluetooth

device is approximately 3 meters (10 feet).

• Any obstacle between this system and a Bluetooth device can

reduce the operational range.

• Keep away from any other electronic device that may cause

interference.

On your device, follow the steps below.

1 Enable it to search for other Bluetooth devices.

2 In the device list, select CMD305A .

3 Enter the default password “ 0000 “.

» If the pairing is successful, [PAIR OK] is displayed.

2 Installation

Connect wires (Fig. 2)

Caution

• Make sure that all loose leads are insulated with electrical tape.

Check the car’s wiring carefully, and then connect them to

the supplied ISO wires. (Fig. 2 - 1)

Connector Connect to

1 Yellow wire The +12V car battery which is live at all

times

2 Blue/White

wire

The electric antenna control lead or power

supply lead of the antenna booster. If there is

no electric antenna or antenna booster, or it

is manually operated telescopic antenna, it is

unnecessary to connect this lead.

3 Black wire A metal surface of the car. Connect the

black ground (earth) lead before connecting

the yellow and red power supply leads.

4 Red wire The +12V power terminal which is live in

the accessory (ACC) position of the ignition

switch. If there is no accessory position,

connect to the +12V car battery terminal

that is always live. Make sure that the black

ground (earth) lead is connected to a metal

surface of the car ﬁ rst.

5 Green and

green/black

wires

Left speaker (rear)

6 White and

white/black

wires

Left speaker (front)

7 Gray and

gray/black

wires

Right speaker (front)

8 Purple and

purple/black

wires

Right speaker (rear)

2 Connect the other end of the supplied standard connector

to the car audio system. (Fig. 2 - 2)

Connector Connect to

1 ANTENNA Antenna for radio

2 External Mic An external microphone for

phone call

3 SUBWOOFER (Socket) Subwoofer

4 REAR LINE OUT L

(Socket)

Rear left speaker

5 Select a source (Fig. 4)

Press repeatedly to select a source.

• [RADIO] : FM/MW radio

• [AUDIO-IN] : the audio that is transferred through the AUDIO-IN

socket

• [BT AUDIO] : the audio that is transferred from a Bluetooth device

• [USB] : When a USB storage device is connected and recognized, you

can select this source to play audio ﬁ les that are stored on it.

6 Listen to radio

Select a radio region

You can select a radio region that matches your location.

1 Press and hold to access the system menu.

2 Press repeatedly until [AREA] is displayed.

3 Rotate to select an option.

• [USA] (United States)

• [EUR] (Western Europe)

• [RUS] (Russia)

• [AUS] (Australia)

• [EAS] (Middle East)

• [ASI] (Asia Paciﬁ c)

• [JAP] (Japan)

• [LAT] (Latin America)

Tune to a radio station

1 Press repeatedly to switch the source to [RADIO] .

2 Press repeatedly to select a band: [FM1] , [FM2] , [FM3] ,

[MW1] , or [MW2] .

3 Press and hold or until the frequency digits blink.

4 Press or repeatedly to tune to a radio station

manually.

» The radio station is broadcast.

• To search for a radio station automatically, press or .

Store stations automatically

1 Press and hold to access the system menu.

2 Press repeatedly until [STORE >] is displayed.

3 Press to conﬁ rm.

» The strongest stations of the selected band are saved in preset

channels automatically.

Note

• You can store a maximum of six stations in each band.

Tune to a preset station

1 Press repeatedly to select a band.

Play audio from a connected device

If the connected Bluetooth device supports Advanced Audio

Distribution Proﬁ le (A2DP), you can listen to tracks that are

stored on the device through the system. If the device also

supports Audio Video Remote Control Proﬁ le (AVRCP)

proﬁ le, you can control play on the system.

1 Connect the Bluetooth device to this system via Bluetooth.

2 Press repeatedly to switch the source to [BT AUDIO] .

» Play starts automatically.

• If play does not start, press .

• To pause play, press again.

• To skip to the previous or next track, press / .

Note

• If the connected device does not support the AVRCP proﬁ le,

control play on the connected device.

Make a call

Note

• Keep the Bluetooth connection active between the system and

your mobile.

Functions Actions

Call a number Dial the number on your mobile and send the

call.

Redial the last

called number

1 Press .

» [Redial] is displayed.

Press to conﬁ rm.

» [CALL---] is displayed.

Pick up an

incoming call

Press

to answer the call.

Reject an

incoming call

Press and hold until [END] is displayed.

End a call

Press

Transfer a

phone call to

mobile

Press and hold

until [TRANSFER] is

displayed.

» The loudspeakers are muted, and the voice comes

from your mobile only.

10 Use the dock

An application Philips CarStudio is available on Google Play

Store for this car audio system. To enjoy full features, download

and install the application to your Android-powered phone.

CMD305A_05_QSG_V2.0.indd 1CMD305A_05_QSG_V2.0.indd 1 1/4/2013 2:42:58 PM1/4/2013 2:42:58 PM

1 2

Podsumowanie treści

Strona 1 - Краткое руководство

Bluetooth V2.1 or laterQuick start guideКраткое руководствоwww.philips.com/welcomeAlways there to help youCMD305ARegister your product and get support

Strona 2 - Android V2.2 or later

Compatible with Android™ Before using the dock, check your Android-powered phone and make sure that it meets the following requirements: • W

Więcej dokumentów dla Odbiorniki samochodowe Philips CMD305A/05

Aby wyświetlić dokument Philips CMD305A/05 Instrukcja Użytkownika

Philips CMD305A/05 Instrukcja Użytkownika (30 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Philips CMD305A/05 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Odbiorniki samochodowe Philips CMD305A/05. Philips CarStudio Car media docking system CMD305A/05 Quick start guide Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Odbiorniki samochodowe Philips CMD305A/05

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Odbiorniki samochodowe Philips CMD305A/05